|
1. Remote Start / Stop of FFH
RCP Can lets you to start and stop of fuel-fired heater by remote control. And certainly, you can use
driver information system to program FFH, as you did it before.
2. Variety of Remote Controls
RCP Can has a set of inputs for easy connection of diverse remotes, like Webasto Telestart (included to
RCP Can T91 Kit), Eberspächer Easy Start, Defa Smart Start
(included to RCP Can
Smart Start Kit), GSM-modules (to control FFH by mobile), alarm systems controls, etc. ♦
|
|
|
|
|
|
|
|
|
|
Note! If you
plan to use RCP Can in conjunction with Smart Start remote control (for example, from Defa WarmUp kit),
we recommend you to order a special version of RCP with Kit documentation / settings and without remote
control in the set. You can make this choice in the purchase section of the Smart Start
Kit. |
|
|
|
|
|
|
|
|
|
|
3. Remote Feedback
|
|
You can get information about FFH operation if remote
control can display it. |
4. Optional Button to Control FFH and LED Functions ♦
An additional
button may be installed on console for one-touch FFH start / stop,
boost mode control and easy settings change.
Button functions:
|
Heater immediate Start |
|
|
|
|
Heater immediate Stop |
|
|
|
One-time boost disable |
|
|
|
One-time boost enable |
LED is used to indicate:
|
FFH boost mode |
|
|
|
|
Run-time errors of FFH |
|
|
|
Confirm the button presses |
5. Embedded Start / Stop of FFH by Ford Remote Key
RCP Can lets you immediately start of fuel-fired heater by original 3-button Ford remote key.
It uses a combination of Lock button presses (3 times by default) to activate this function. A back-up remote is always
with you now.
|
|
|
6. FFH Start and Work Indication by Turn Signals
RCP Can may flash by the turn signals in rear-view mirrors to inform you that the heater has
started and operates. It's adjustable function, which may be switched on or off (as default).
7. Extended Control of Boost Heat Mode
RCP Can has several adjustable functions to control the boost heat mode of FFH:
|
Boost heat mode disabling by the coolant temperature: RCP Can doesn't let
FFH start with engine, if its temperature is higher than programmed one. It can be useful to prevent FFH
from short run cycles, which result in clogging of FFH. |
|
|
|
Boost heat mode permanently enabled / disabled by module RCP |
|
|
|
One-time enabling of the boost heat mode by additional button
(if boost heat mode permanently disabled by module RCP) ♦ |
|
|
|
One-time disabling of the boost heat mode by additional button. This
function is may be useful to short trips, for example. ♦ |
|
8. Main Battery Protection from Discharging
Fuel-fired heater uses energy of the vehicle's main battery to work, not only fuel.
RCP Can may control a level of battery voltage to prevent the battery from discharging.
The level can be
adjusted in accordance of battery condition. Also you can limit time of autonomous work of FFH.
|
9. Errors Reset (Unblocking)
If your heater doesn't burn after start, the ECU of FFH stops the heater and fixes an error
in memory. After 5 unsuccessful starts FFH is being blocked. If a problem is not caused by FFH malfunction
(ex. exhaust system is clogged by snow), it can be enough to reset ECU errors by RCP.
|
|
|
|
|
|
|
|
|
|
Please pay attention, this function may be used only for that vehicle, in which it was activated
for the first time. |
|
|
|
|
|
|
|
|
|
|
|
|
|
10. Control of External Devices ♦
RCP Can allows you to control external devices while the heater operates.
Functions and examples of their use:
|
|
|
|
Disconnection of consumers during the heater operation to conserve
battery power (for example, turning off the climate control fan) |
|
|
|
Disable highly sensitive sensors of additional alarm system to
prevent false alarm triggering when the heater operates |
|
|
11. Plug and Play or Permanent Installation
RCP Can may be connected:
|
|
|
|
To the OBD-II diagnostic connector on the dashboard
using a special cable (included). The module is fixed on the back side of the dashboard (or into
the small glove box in Focus) with tape. PnP-connector and wiring are hidden under the cover
of the OBD connector. |
|
|
|
Hidden easy permanent connection to the OBD II wires with
quick splice connectors |
|
|
|
Hidden permanent connection to the car wiring |
|
|
12. Compatibility
RCP Can is compatible to Ford Focus, C-Max and Kuga models, factory equipped with Eberspächer
Hydronic fuel-fired heaters BE5WS and D5WS:
|
Ford Focus 3 |
2010—... |
|
|
|
|
Ford Kuga 2 |
2012—... |
|
|
|
|
Ford C-Max 2 |
2010—... |
|
|
|
|
Ford Grand C-Max |
2010—... |
|
♦ This functions can be used only with permanent connection to the car wiring |
|
|
|
|